您要查找的是不是：
- Effect of Mates and Slide Rate on Wear Resistance of the Surface Strengthened by Electrical Discharge Under Large Contacting Stress 大接触应力下配副及潜滑率对电火花强化层磨损特性的影响
- large contacting stress 大接触应力
- If the conical angle difference is too large, the anchorage length will minish and the contact stress of CFRP bars will increase. 锚具长度越长,对碳筋的受力越有利,碳筋所受接触压应力的峰值也越小;
- Simulation test of packer rubber-casing wall contact stress. 封隔器胶筒对套管接触应力模拟试验研究。
- When the working load is large, the contact stress between cam surface and follower ends becomes the main cause of cam mechanism failure. 当工作载荷较大时,凸轮表面和从动件端部的接触疲劳破坏就成为凸轮机构失效的主要形式之一。
- In view of the different offsets and the bearing clearances of offset mono-cone bit,with the key analysis of the contact stress at the journal bottom of large journal ... 轴颈底部的接触应力随偏心距增大而增大,且在正常公差范围内的间隙变化对接触应力的影响不明显;止推面上端的接触应力比下端大,制造时应加强止推面上端的强度和硬度。
- Soft grade for the larger contact area. 接触面积大时用软的结合度。
- Coarse grain size for the larger contact area. 接触面积大时用粗的粒度。
- This method is also applicable to solving contact stress and residual stress. 该方法同样适用于解决接触应力和残余应力问题。
- The sealing contact stress is an important parameter of sealing capability. 密封接触应力是影响密封性能的重要技术参数。
- Bearings having a large contact angle are a special design of the TDI configuration (fig 9). 有大接触角度的轴承是TDI配置的特殊设计(图9)。
- The research result states that the contacting stress, thread torque and thread joggle geometry restriction are mechanical points of the sticky thread. 研究结果表明:接触应力、上扣扭矩、螺纹啮合时的几何约束,是齿面粘扣的力学要点。
- Bearing with large contact angle, intermediate ring between the outer rings and pressed steel cages (fig 9). 带有大接触角度、外圈之间的中隔圈和钢板冲压保持架的轴承(图9)。
- PLC main control tie-in hominize interface, large contact type liquid crystal display, easy operation, easy decode. 主控制采用PLC搭配人机界面，大型触控式液晶荧屏，使操作简单，判读容易。
- First contact stress and deformation of parts which have normal shapes and simple contacting status are calculated using Hertz formula and finite element method. 首先,运用了赫兹公式和有限元法对外形规则、接触状态简单的零件进行接触应力和接触变形计算。
- Bearing with large contact angle, intermediate ring between the outer rings, pierced rollers and steel pin-type cages (fig 15). 带有大接触角度、外圈之间的中隔圈、穿孔滚子和钢支柱式保持架的轴承(图15)。
- Self-retaining bearing units with large contact angle, outer rings held in a retention sleeve, pierced rollers and steel pin-type cages (fig 10). 带有大接触角度、夹在保持套筒里的外圈、穿孔滚子和钢支柱式保持架的自保持式轴承组件(图10)。
- Beased on the theory of Hertz stress, the contact stress of roller bearing is analysed in this paper. 摘要依据赫兹接触强度计算理论，着重研究了圆柱滚子轴承内、外圈及滚动体的接触应力。
- It is difficult to research the contact stress in the seal interface with fitting and using seal components. MARC，建立了橡胶O形密封圈和油封轴对称有限元模型，对其安装和使用过程中的接触变形、接触宽度上的接触应力分布等进行了分析，从而为进一步可靠设计、优化橡胶密封件提供了理论依据。
- Please select the contactors with a larger contact current-carting rating. 请选用能通过较大额定电流的接触器。
以上内容独家创作，受著作权保护，侵权必究
海词词典，十七年品牌
